Outboards - Outboard Steering Systems

• For Mercury Outboards with Existing Wingplate
• Replacement Ram Assembly
• 9" Stroke Ram
• (2) 16" SS Hoses, (2) Thru Hull Fittings, (2) Ram Fitting Included.

• Inside Steering Kit for Outboards. Options with 1 or 2 steering rams.

Standard Single Ram Power Steering for Mercury 300R

The IMCO Standard Single Ram Power Steering System is intended for Mercury 300 R powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

Note: These kits contain non-assembled rubber hoses and brass fittings. See steering component section for stainless steel braided line options.

Standard Dual Ram Power Steering for Mercury 300R, No Tie Bar, Outside Only

The IMCO Standard Single Ram Power Steering System is intended for Mercury 300 R powered recreational performance sport boats and used primarily in moderate water conditions. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

Note: These kits contain non-assembled rubber hoses and brass fittings. See steering component section for stainless steel braided line options.

Standard Single Ram Power Steering

The IMCO Standard Single Ram Power Steering System is intended for Evinrude E-Tec 250 HO Motor powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

Note: These kits contain non-assembled rubber hoses and brass fittings. See steering component section for stainless steel braided line options.

For parts list, and to buy replacement parts click here

Standard Single Ram Power Steering

The IMCO Standard Single Ram Power Steering System is intended for Mercury XS powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

For parts list, and to buy replacement parts click here

Standard Single Ram Power Steering for Mercury 300 X

The IMCO Standard Single Ram Power Steering System is intended for Mercury 300 X powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

Note: These kits contain non-assembled rubber hoses and brass fittings. See steering component section for stainless steel braided line options.

For parts list, and to buy replacement parts click here

Standard Single Ram Power Steering for Mercury 2.5 EFI

The IMCO Standard Single Ram Power Steering System is intended for Mercury 2.5 EFI powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds. Kit includes Tilt pin, Steering Ram, Wing Plate Outside hoses and thru hulls.

Do it yourself. Install a single ram steering system in approximately four hours or less.

For parts list, and to buy replacement parts click here

Dual External Hydraulic Steering For 2 Mercury XS Stern Drives

IMCO's external hydraulic steering for the Mercury XS has been designed, engineered and tested to eliminate side-to-side drive unit "play", a major contributor to high speed chine walking IMCO's power steering system is ultra heavy-duty throughout. The  IMCO steering systems are easily installed and priced more affordably than other less efficient alternatives.

Note: These kits contain non-assembled rubber hoses and brass fittings See steering component section for stainless steel braided line options.

For parts list, and to buy replacement parts click here

Dual External Hydraulic Steering For 2 Mercury 300 X Drives

IMCO's external hydraulic steering for the Mercury 300X has been designed, engineered and tested to eliminate side-to-side drive unit "play", a major contributor to high speed chine walking IMCO's power steering system is ultra heavy-duty throughout. The  IMCO steering systems are easily installed and priced more affordably than other less efficient alternatives.

Note: These kits contain non-assembled rubber hoses and brass fittings See steering component section for stainless steel braided line options.

For parts list, and to buy replacement parts click here

Standard Dual Ram Power Steering for Dual Mercury 2.5 EFI

The IMCO Standard Dual Ram Power Steering System is intended for Dual Mercury 2.5 EFI powered recreational performance sport boats. Once installed, boat drivers will experience significantly more precise steering control, especially at higher speeds.

Do it yourself. Install a single ram steering system in approximately four hours or less.

Note: These kits contain non-assembled rubber hoses and brass fittings. See steering component section for stainless steel braided line options.

For parts list, and to buy replacement parts click here

Hyco Front Mount Outboard System for 150hp and Less. Includes: UC94-OBF cylinder (Not suitable for HONDA®BF115 and BF130 engines and Mercury® Optimax TM75, 90, 115.) Available with Standard or Tilt Helm.

Featuring the unique split tilt tube rod that allows for installation of the UC94 cylinder without removing the engine the Hyco is an easy and affordable outboard hydraulic steering solution for boats with 150 horsepower and under. Coupled with the UP20 helm the Hyco offers effortless steering with 5 turns lock to lock. And it is applicable to almost all 2 and 4 stoke outboards engines.

This kit includes Hydraulic Ram, Hydraulic Helm and 2 Quarts of Oil.
Steering Wheel, Hose and fittings are sold separately!

See Application Guide on Additional Info Tab to make sure you order the correct cylinder.

Protech Hydraulic Helm Steering, for application up to 300HP. Available with Standard or Tilt Helm

Larger horsepower applications require a more robust steering cylinder. The Uflex Protech cylinder is designed for single, dual and triple engine applications up to 300 hp per engine. Featuring heavy duty seals, 304 electro-polished link assemblies, and a carbon steel piston, it is built for the most demanding applications.

This kit includes Hydraulic Ram, Hydraulic Helm and 2 Quarts of Oil. Steering Wheel, Hose and fittings are sold separately!

See Application Guide on Additonal Info Tab to make sure you order the correct cylinder.

SILVERSTEER Front Mount Outboard System for 350hp and Less. Includes: UC128-SVS cylinder. Available with Standard or Tilt Helm.

Specifically designed for high performance and high torque applications, the SilverSteer features a 1,500 psi helm and keyed bullhorns on the cylinder for maximum durability and minimal lost motion.

Whether a bass boat, flat boat or tournament style offshore fishing boat, the SilverSteer™ will deliver smooth, responsive and precise steering.

Adjustable boss style fittings allow precise hose routing without the risk of breaking the fittings by overtightening or leaking fittings from loosening during installation, a common problem on competing cylinders.

• Horsepower: Single engine, up to 350hp, dual engines, up to 600hp (total)
• Helm: 7.3 cu in/120cc
• Hose: 1,500psi
• Turns Lock-to-Lock: 4.3
• Included Equipment: UP28 F-SVS front mount helm pump, UC128-SVS front mount outboard cylinder, hydraulic oil (two qts.), Hose kits sold separately
• Steering Wheel Shaft: 3/4" tapered
• Warranty: Two years

This kit includes Hydraulic Ram, Hydraulic Helm and 2 Quarts of Oil. Steering Wheel, Hose and Thru Hull fittings are sold separately!

See Application Guide on Additonal Info Tab to make sure you order the correct cylinder.

This panel has two fittings that are used for feeding Uflex Outboard Hydraulic Lines through a bulkhead. Available in Black, White, or Chrome.  The fittings are 3/8" compression fittings on both sides. The standard 3/8" compression is equal to 9/16"-24 UNEF 2A thread.

This is a pair of 3/4" fittings that are used for feeding Uflex Outboard Hydraulic Lines through a bulkhead or transom. These are 3/4" diameter x 2.6" long. They have 3/8" compression fitting connections.