You can't feel them or hear them, but harmonic vibrations are at work inside every internal combustion engine. That's not good. Similar to glass-shattering forces created by a high pitched note, harmonic vibrations cause metal fatigue and can cause significant power loss because crankshaft harmonics are transmitted to the camshaft and valvetrain. Control this power-robbing force with a Fluidampr harmonic damper that uses race proven vibration damping technology. A high viscosity silicone fluid surrounds a nylon-coated inertia ring inside a laser welded housing. All dampers are coated with a black zinc chromate finish for increased corrosion resistance. Timing marks - every two degrees from 50° BTDC to 10° ATDC with additional marks at 90, 180 and 270. Meets SFI 18.1 specs. Made In The USA.
Runner Length – 6.29”, As-Cast Runner Cross-Sectional Area – Tapered 4.67in² to 2.84 in²
Throttle Body Flange Location, with 92/102mm EFI Plenum Top : Height – 8.42” (from engine block lifter valley cover flange), Longitudinal Location – 3.84” (forward from engine block front flange), Angle – 25 deg. (down from vertical)
Plenum Top Gasket Type – 3/32” Round O-ring Cord
Mounting Flange Gasket Type – Standard LS3 Molded O-Ring
Port Size – 2.49” Height x 1.21” Wide
Total Height with 92/102mm EFI Plenum Top – 12.32” to the lifter valley cover flange on engine block.
Base Plenum Top Mounting Flange Height – 8.42” to the lifter valley cover flange on engine block.
These parts should be used for the following applications: Racing/Performance/Street Rodder where hood restrictions are NOT a consideration. Top can be mounted forward or backward.
Holley EFI LS main harnesses have a map sensor connecter designed for use with an LS1/2 style map sensor. The 558-416 is an adapter harness that can be used to adapt any LS harness that uses a LS1/2 MAP sensor connection to a LS3 MAP, which is recommended for this manifold.
Crankshaft torsional vibration protection across RPM range.
Reduce risk of crankshaft failure & wear on critical engine parts.
Unleash lost torque and horsepower.
Replaceable crankshaft hub.
SFI 18.1 certified.
Made in USA.
The steel damper is finished in a corrosion resistant black zinc chromate,
then laser engraved with a Fluidampr – Made in the USA logo and SFI 18.1
credential. The front and rear bolt-on Supercharger and air-conditioning
aluminum pulleys have a hard coat anodized finish.
Got an LS engine to get running? Nothing is easier than bolting on a carburetor. Holley's dual plane carbureted intake for GM's LS engines will help you get on the streets quick!
Its dual plane design makes it perfect for low end torque, yet it still pulls all the way to 6,500 RPM! Our O–ring cylinder head mounting flange gaskets provide an OEM style seal and make installation a snap. Bolt one on today!
Features:
1500-6500 RPM power band
4150 Square bore flange
Optimized runner layout and constant cross sectional area - broad torque curve, best vehicle performance from 1500-6500 RPM
Minimum carb flange height means it fits in vehicles with minimal or no hood modifications
Great for carbureted or throttle body EFI street applications
Cast aluminum construction and efficient casting design for light weight, consistent wall thicknesses and improved casting quality
Weighs 15.14 lbs.
Height (front) - 5.07" from front lifter valley cover to carb mounting flange
Height (rear) - 6.14" from rear lifter valley cover to carb mounting flange
Port size - 2.72" height x 1" wide
Mounting flange gasket type - O-ring
Includes Viton® O-rings - Viton® is a registered trademark of DuPont Performance Elastomers
This LS alternator bracket fits the 4.8, 5.3 and 6.0 iron block engines with the iron lower stock pulley. It mounts to the upper port cylinder head with the 2 supplied metric bolts. The bracket fits the Denso style 7si case alternators with 2 options available. The 70 amp 602-20112 and the 100 amp version 620-3146. This is available as a bracket only or as a kit which includes the bracket, alternator, and belt which is part number 625-8551.