462-34-ARG1000SBSPP Standard single strainers. No tie rods or leaks under pressure or vacuum. Quick and easy mounting system allowing removal of strainer without tools. #304 Stainless steel filter basket. O-ring seals at strainer cap and between strainer head and sight glass. See-thru screw-on strainer cap allows easy, no-tools maintenance. Spanner wrench holes in cover allow the use of SW-2531 wrench. Install with pipe or hose. Do not use chemical or abrasive cleaners on sight glass. NOT TO BE USED IN POTABLE WATER SYSTEMS. Ports: 1" NPT, Basket: Stainless, A: 9", B: 5.8", C: 6.5", D: 2.0" Standard single strainers. No tie rods or leaks under pressure or vacuum. Quick and easy mounting system allowing removal of strainer without tools. #304 Stainless steel filter basket. O-ring seals at strainer cap and between strainer head and sight glass. See-thru screw-on strainer cap allows easy, no-tools maintenance. Spanner wrench holes in cover allow the use of SW-2531 wrench. Install with pipe or hose. Do not use chemical or abrasive cleaners on sight glass.NOT TO BE USED IN POTABLE WATER SYSTEMS.
|
|
462-34-TH100W Should have threaded portion cut to proper length considering hull and butt block thickness. Consider thread depth when using a seacock. Sealant is recommended between hull and thru-hull flange. Has locknut with bonding screw. Comes with nut. NOT TO BE USED IN POTABLE WATER SYSTEMS. Thread: G 1", A: 2.85", B: 0.30", C: 2.32" Should have threaded portion cut to proper length considering hull and butt block thickness. Consider thread depth when using a seacock. Sealant is recommended between hull and thru-hull flange. Has locknut with bonding screw. Comes with nut.NOT TO BE USED IN POTABLE WATER SYSTEMS.
|
|
This Part has options, please click the button below to order.
137-9276 1" Tie Bar. Please measure length from female threaded end to center of hole on face of opposite end. Price shown is for tie bars up to 36". Please contact sales for quote if you need a longer tie bar. Rule of thumb: These bar are approximately 4.5" shorter than the center to center of the drives. Female thread is 3/4"-16. Hole on the face of the opposite end is 1/2".
|
|
462-87-BONITO Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1" dia., OD: 1-1/2", Length: 4", Metal Wall: 1/8", Johnson Name: BALE, BF Goodrich Name: Kayak Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-BETTA Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1" dia., OD: 1-1/4", Length: 3", Metal Wall: 1/32", Johnson Name: -, BF Goodrich Name: - Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-BLACKFISH Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1" dia., OD: 1-1/4", Length: 4", Metal Wall: 1/32", Johnson Name: BACK**, BF Goodrich Name: Kava Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-BLOATER Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1" dia., OD: 1-3/8", Length: 4", Metal Wall: 1/16", Johnson Name: BAIT**, BF Goodrich Name: - Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-87-BROADBILL Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length 36 sq." bearing area x 35 psi 1,260 lbs. Is bearing load capacity Shaft: 1" dia., OD: 1-5/8", Length: 4", Metal Wall: 1/8", Johnson Name: BAND*, BF Goodrich Name: Kefer Pollution-Free Naval Brass Marine BearingsBrass sleeve with rubber oil resistant shaft. The clean bearing that cushions the shaft, installs in minutes and lasts for yearsMorse Bearings are engineered to meet the toughest service requirements in corrosive and abrasive marine or industrial applications. The fluted rubber bearings surface will outlast hard surface bearings by more than 10 times. All materials meet U.S. Navy specs MIL-B-17901A CLII.Bearing Selection: Normal design practice is to select a bearing with a length equal to 4 times the shaft diameter.It may be acceptable to deviate from this rule when application load requirements permit the use of shorter bearing lengths. * Slimline Bearing.Bearing area is: Bearing I.D. (shaft diameter) multiply x bearing length. Loading capability is determined by: Multiplying that bearing area x 35 psi.Example: (RAY)- 3" shaft dia. x 12" length = 36 sq. Inch bearing area 36 sq. Inch bearing area x 35 psi = 1,260 lbs. Is bearing load capacity
|
|
462-88-1501006 For sink, shower, cooler, refrigerator and live well drain lines. Also supply line for non-pressurized water system. Made of FDA approved single layer vinyl non-toxic compound. Not recommended for hot water or pressurized systems. ID: 1", OD: .125", Length: 50', Working Pressure: 20# (70° F) Shields Clear PVC Tubing has a single layer FDA formula vinyl. This hose is primarily used for nonpressurized potable water system supply and drain lines (sink, shower, icebox). This hose is NOT for use in hot water or pressurized water systems.
|
|
462-606-1401006 Features extra odor-resistant sanitation hose for all head and holding tank connections smooth light grey hose, hard PVC helix gives good flexibilty and bend radius. NOT for potable water applications, or for exposure to alcohol, petrochemicals or solvents. Maximum operating temps (+10° to140°F). Maximum working pressure 70 psi. 3 Year warranty. ID: 1", Length: 50', Bend: 5", VAC: 28
|
|
462-180-80015 Slow-drying, non-hardening sealant designed for sealing cut gaskets and stamped parts. Allows for easy disassembly if required. Temperature range -65°F to 400°F (-54°C to 204°C); resists common shop fluids and fuels. Use where sealing is more important than adhesion Size: 1-1/2 oz. tube, Case: 12 Sold: Each
|
|
462-38-44103 Brass 90° with female/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2" Sold: Each
|
|
462-38-28087 Imported. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-38-44183 Brass 45° with female/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-38-44163 Bronze 90°, male/female threads. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-38-44473 Bronze NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-38-44413 Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-38-44253 Bronze and imported. NOT TO BE USED IN POTABLE WATER SYSTEMS. Size: 1/2"
|
|
462-9-0322DP4PLB "Cast bronze. Flange is machined to fit hull and grooved to retain bedding compound. Neck is threaded to approximately 3/8" from flange. Includes flange nut. UL Listed. NOT TO BE USED IN POTABLE WATER SYSTEMS." Hose: 1/2", Flange: 1-1/2", Max Hull Thickness: 1-3/8" Sold: Each
|
|
462-88-1680126 For hot or cold pressurized water system supply, washdown pump connections, and head intake hose. Clear, extra heavy duty wall, polyester reinforced PVC. FDA formula vinyl. 50' Roll out cartons. ID: 1/2", OD: 3/4", Length: 50'
|
|
