Your shopping cart is currently empty.
Bravo One - Serial 0W250000 and Up - Gimbal Housing
Section Drawing: (Hover or click to view larger)
Other Sub-Sections:
- Bell Housing
- Compact Hydralic Steering Actuator
- Continuity Kit
- Driveshaft Housing and Drive Gears
- Gear Housing (Brave One)
- Gear Housing (Bravo Three)
- Gear Housing (Bravo Two)
- Gear Lube Monitor Components
- Gimbal Housing
- Gimbal Housing Cover
- Gimbal Ring and Steering Lever
- Gimbal Ring and Steering Lever, AXIUS Gen I
- Mercathode Kit
- Power Steering Actuator
- Special Tools-Driveshaft Housing
- Special Tools-Gear Housing (BRAVO ONE)
- Special Tools-Gear Housing (BRAVO THREE)
- Special Tools-Gear Housing (BRAVO TWO)
- Special Tools-Transom
- Steering Actuator, Axius (Gen I), Sensors Screw In
- Steering Actuator, Axius (Gen I), Sensors w- E-Clip-End Cap
- Steering Actuator, Axius (Gen II)
- Sterndrive Unit Chart, BRAVO I-II-III (Standard)
- Transom Assembly Chart
- Transom Plate and Shift Cable
- Trim Cylinder Components
- Trim Cylinders and Hydraulic Hoses (Standard Transoms)
- Trim Pump and Motor Components
- Trim Pump Assembly (Complete)
- Universal Joint and Shift Components
| Ref. | OEM Part # | Hardin # | Mallory # | GLM # | Other # | Description | Num Req. | Superceded From | Special Notes |
| 1 | 8M0062517 | GIMBAL HOUSING ASSEMBLY | 1 | 43881A17 | |||||
| 1 | 866454A02 | GIMBAL HOUSING ASSEMBLY | 1 | (SEACORE) | |||||
| 2 | 16-56296 | STUD, (.437-20 x 4.750) | 4 | ||||||
| 2 | 16-866562 | STUD, (.437-20 x 4.750) Stainless Steel | 4 | (SEACORE) | |||||
| 3 | 16-818834 | STUD, (.437-20 x 4.250) | 4 | ||||||
| 3 | 16-866563 | STUD, (.437-20 x 4.250) Stainless Steel | 4 | (SEACORE) | |||||
| 4 | 23-983571 | BUSHING, Lower | 1 | ||||||
| 5 | 26-8M2005029 | SEAL, Oil | 1 | 26-416071 | |||||
| 5 | 12-866451 | SEAL | 1 | This Part is No Longer Available | |||||
| 6 | 23-98356 | BUSHING, Upper | 1 | ||||||
| 7 | 22-74036 | FITTING, Grease | 1 | (Use with greased bearing) | |||||
| 7 | 8M2015913 | PLUG, (.250-28 x .320) | 1 | (Use with non-greased bearing) | |||||
| 8 | 19-77633Q | LUBRICAP | 1 | ||||||
| 9 | 26-88416 | SEAL, Oil | 1 | ||||||
| 10 | 879194A01 | BEARING ASSEMBLY | 1 | 30-862540A3 | |||||
| 11 | 61075 | TOLERANCE RING | 1 | ||||||
| 12 | 8M0068607 | SEAL KIT, Without tabs | 1 | ||||||
| 12 | 8M0068609 | SEAL KIT, With tabs | 1 | This Part is No Longer Available | |||||
| 13 | 16-56766 | STUD, (.250-20/.250-28 x 1.380) | 2 | ||||||
| 14 | 43713 | SEAL | 1 | ||||||
| 15 | 32-43437 | HOSE, Water | 1 | ||||||
| 16 | 41674T | INSERT | 1 | 41674 | |||||
| 17 | 17-8M0073409 | SWIVEL PIN, Lower | 1 | 17-99353 | |||||
| 18 | 18-54929 | COTTER PIN | 1 | ||||||
| 19 | 12-32518 | WASHER | 1 | ||||||
| 20 | 865470 | HOUSING, Inlet, Male Quick Connect | 1 | ||||||
| 21 | 27-441081 | GASKET | 1 | ||||||
| 22 | 10-78038 | SCREW, (.250-20 x 1.75) | 2 | ||||||
| 22 | 10-73015 | SCREW, (.250-20 x 1.75) | 2 | ||||||
| 23 | 13-21272 | LOCKWASHER, (.250) | 2 | ||||||
| 23 | 13-78968 | LOCKWASHER, Internal (.250) | 2 | ||||||
| 24 | 74639A2 | BELLOWS ASSEMBLY, Shift Cable | 1 | ||||||
| 25 | 54-866507 | 676-9-73115 | 700-21790 | CLAMP | 1 | ||||
| 26 | 54-815504320 | CLAMP, Worm Gear | 1 | ||||||
| 27 | 12-34567 | WASHER | 8 | ||||||
| 27 | 12-35935 | WASHER, (.435 x .875 x .105) Stainless Steel | 8 | ||||||
| 28 | 11-82670815 | NUT, (.437-20) | 8 | ||||||
| 29 | 27-988231 | GASKET | 1 | ||||||
| 30 | 8M0080805 | MANIFOLD ASSEMBLY | 1 | 98825A4 | |||||
| 31 | 13-78968 | LOCKWASHER, Internal (.250) | 2 | ||||||
| 32 | 11-8267119 | NUT, (.250-28) | 2 | ||||||
| 33 | 22-428611 | FITTING, Pipe - Brass (.750-14) | 1 | ||||||
| 34 | 19-861492 | PLUG, Trim Switch Wires | 1 | ||||||
| - | 22-88847A1 | PLUG KIT, Access Hole | 1 | (Access Hole Plug Kit contains all necessary parts to allow removal of swivel shaft without removing Gimbal Housing) |