137-8147 Kit Includes:
- 2 Nuts and washers
- 1 Trim Ram Pin with Actuator provision
- 1 Trim Table Cable End with nut and washer
- 4 Bushings
- 2 Spacers
|
|
137-8119 These are rebuild kits for #137-8005 trim rams.
- 137-8013, GLAND, HD TRIM RAM, 1
- 137-8014, PISTON, HD TRIM RAM, 1
- 137-8129, SEAL, WIPER - HD TRIM RAM, 1
- 625-1116, O-RING, 3
- 625-1135, O-RING, 1
- 625-1325, O-RING, 1
|
|
137-8149 This kit includes one trim tab pin, two nuts, two washers, two bushings and two upper trim ram spacers.
|
|
This Part has options, please click the button below to order.
625-4103 Gen 4 Stainless Steel Pump And Bracket Mercury Sea Pump Assembly Serpentine - BBC
These are new Stainless Steel replacement sea pumps. We have configured options so that you may buy just a replacement pump only or bracket only or even an entire replacement pump assembly including the mounting bracket, Serpentine pulley and mandrel. This model include a beautifully polished billet bracket and Serpentine Pulley and Mandrel.
NOTE: Billet bracket cannot be used in Circ Pump applications!
|
|
625-4109 New Gen 4 Stainless Steel Mercury Pump Assembly with Stamped Steel Bracket & Billet V-Groove Pulley - BBC Applications
These are new Stainless Steel replacement sea pumps. We have configured options so that you may buy just a replacement pump only or bracket only or even an entire replacement pump assembly including the mounting bracket, V-groove pulley and mandrel.
|
|
625-4221 Gen 5/6 Sea Pump Vent Equalizer
This kit is designed to allow venting of pressure build up inside the Sea Pump housing that could create premature failure to be released through the existing fuel pump vent system.
Note will work with all sea pumps listed below that the front housing has been tapped for 1/8 NPT:
Will not work on 625-4112 with plastic rear housing.
|
|
625-4312
Replacement 496 Sea Pump Axius 7" Pulley and Mandrel Kit
This billet pulley is designed as a replacement for popular MerCruiser Axius applications. Will fit stock MerCruiser or Hardin Gen 7 Pump. For 350, 496, 502 Mag with 7" diameter Axius pulley applications only. Includes mandrel and bolts.
|
|
625-4278
Replacement 496 Sea Pump Pulley and Mandrel Kit
This billet pulley is designed as a replacement for popular MerCruiser applications. Will fit stock MerCruiser or Hardin Gen 7 Pump. For 350, 496, 502 Mag with 5-3/4" diameter pulley applications only. Includes mandrel and bolts. This kit includes #13 - #16 on the Gen 7 Sea Pump Breakdown. Replaces OEM Mercury# 8M0150724.
|
|
This Part has options, please click the button below to order.
625-4209 If you are having trouble installing impellers in Gen 7 Sea Pumps this handy tool allow for easy installation in less than 30 seconds!
|
|
420-900006
- Fits Hardin, Hardin Marine, Power Torque and Mercury Hi-Performance
- Replace your worn out hoses, or have a spare on hand!
- 1" Inside Diameter
- 6-1/2" Center to Center
|
|
900-37C150HH5 Gil Manifold 1.5" Exhaust Bolt
|
|
900-37C300HH5 Gil Manifold 3" Exhaust Bolt
|
|
900-37SASTZN Gil Manifold Exhaust Bolt Washer
|
|
420-425708 Gil Manifold Inlet Tee Fitting
|
|
420-425710 Gil Manifold L Fitting
|
|
625-2002 Gil Manifold Pipe Plug
|
|
900-37CNFNSS Gil Manifold Rise Stud Nut
|
|
420-100 Gil Manifold Riser Stud
|
|
900-37SASTSS Gil Manifold Riser Stud Washer
|
|
420-425709 Gil Manifold Tee Fitting
|
|
420-906515 Gil Manifold Water Tree Hose
|
|
620-902020 Gil Replacement Dry Big Gun Tailpipe - 4-1/2" O.D x 4" I.D.
This pipe can be used as a replacement or as an upgrade to build the very
most power with a dry exhaust system. The popular Big Gun pipe has been a
favorite of customers with large supercharged engines.
|
|
620-902530 Gil Replacement Dry Offshore Tailpipe - 4" O.D x 3-1/2" I.D. (Sold As A Pair)
This pipe can be used as a replacement or as an upgrade to build the very
most power with a dry exhaust system.
|
|
410-1499
- Constructed from 316L Stainless Steel.
- For BBC or SBC applications.
- Features (3) 1" push-on hose barbs.
- This unit is used in crossover cooling system #620-300100.
- Length 4-1/4", Height 3", Width 2-3/4".
- Includes bolts and O-ring.
- O-Ring sealed, no gaskets required!
|
|
620-96490
- Chrome Coil Bracket, mounts on GM, Chevy Intakes.
- Easy mounting of most original and aftermarket coils.
- Secure & attractive mount in any boat.
|
|
625-4117 Hardin Marine is the first to bring a engine specific sea water pump for the popular LS series of engines. This dual stage sea water pump was designed around the 5.3 ,6.0, and 6.2 liter generation engine platforms. The pump uses Hardin Marine's Extreme Lifetime Series stainless steel impeller housing as well as a proprietary short body construction that allows the necessary access or clearance for the engines factory engine mounting pads when the pump is installed. The pump is designed to mount to the engine blocks factory A/C mounting bosses while positioning the billet aluminum serpentine pulley in line with OEM crankshaft pulley. The billet mounting bracket provides the two necessary idlers that allow this pump to be incorporated into most factory automotive serpentine accessory drive systems. The Sea pump features female (2) 1" NPT and (1) 1-1/4" common inlet and outlet ports for ease of plumbing convenience.
Note: Fits OEM GM LS Corvette / CTS-V / G8 automotive balancer spacing with 1-1/2" offset (NOT Truck or F-Body balancer)
|
|
625-4116 Hardin Marine is the first to bring a engine specific sea water pump for the popular LS series of engines. This single stage sea water pump was designed around the 5.3 ,6.0, and 6.2 liter generation engine platforms. The pump uses Hardin Marine's Extreme Lifetime Series stainless steel impeller housing as well as a proprietary short body construction that allows the necessary access or clearance for the engines factory engine mounting pads when the pump is installed. The pump is designed to mount to the engine blocks factory A/C mounting bosses while positioning the billet aluminum serpentine pulley in line with OEM crankshaft pulley. The billet mounting bracket provides the two necessary idlers that allow this pump to be incorporated into most factory automotive serpentine accessory drive systems. The Sea pump features female 1" NPT inlet and outlet ports for ease of plumbing convenience.
Note: Fits OEM GM LS Corvette / CTS-V / G8 automotive balancer spacing with 1-1/2" offset (NOT Truck or F-Body balancer)
|
|
