Engine Parts - Power Steering Pumps

Fits KRC Power Steering Pumps with Splined Shaft

High Speed Saginaw Style Power Steering Pump - 1500 PSI

This all new performance power steering pump is a direct replacement for most GM P-series Saginaw OEM power steering pumps. These pumps produce an increase of pressure thus aiding in low speed steering response.

NOTE: Reservoir is sold separately.

Why is this pump better?

• The bearing snout is machined to replace the stock bronze bushing with #203 needle bearing.
• The shaft is machined from 4140 tool steel and is heat treated to 75/80 Rockwell. Will not break if you dead head the pump.
• The shaft has dual thrust washers to insure control forward and rear movement when under load.
• The main boring housing is machined to a larger diameter to clean up wore surface. Larger ring, rotor and vanes are installed.
• The main oil passage is enlarge for greater flow
• Flow valve bore is machined larger. Unit comes with larger valve and spring.
• Our pumps flows 4-3/4 to 5-1/4 GPM. Double the output than a stock Saginaw "P" series pump.
• Comes with new o-rings for installation

KRC Pro Series III Power Steering Pump

KRC Pro Series III Power Steering Pump 5.9CC W/ 17 Spline & Threaded Shaft for Pulley. Pulley Sold Separately. STD -10 Inlet W/ STD -6 Flow Control Fitting. KRC Series III Pumps are quickly adjustable for the ultimate in driver feel. Weighs on 2.58 lbs. & draws up to 50% less HP than competing pumps. 3.1 GPM

This is an all new high performance power steering pump designed as a replacement for most mercury and mercruiser style steering pumps. This pump features numerous improvements over the factory unit.  These pumps produce an increase of pressure thus aiding in low speed steering response.

 Why is this pump better than a OEM stock pump?

• The bearing snout is machined to replace the stock bronze bushing with #203 needle bearing.
• The shaft is machined from 4140 tool steel and is heat treated to 75/80 Rockwell. Will not break if you dead head the pump.
• The shaft has dual thrust washers to insure control forward and rear movement when under load.
• The main boring housing is machined to a larger diameter to clean up wore surface. Larger ring, rotor and vanes are installed.
• The main oil passage is enlarge for greater flow
• Flow valve bore is machined larger. Unit comes with larger valve and spring.
• Our pumps flows 4-3/4 to 5-1/4 GPM. Double the output than a stock Saginaw "P" series pump.
• 1500 PSI max
• Sold Complete with black housing, pump, vented cap,  3/8" barb inlet,  5/8" - 18 female inlet, press on pulley or flange not included, no keyway

Power Steering Pump, Pulley, Reservoir & Billet Port Cylinder Head Mount Kit

This kit offers all the necessary components to add a complete power steering pump assembly to your engine. This performance inspired pump produces 1200 psi at 800 RPM and 1500 psi at 1200 RPM. This pump features an oil reservoir attached to the pump and uses the popular JIC style fittings for ease of installation. A precision machined billet cylinder head mounting bracket and Tru-Trac billet V-groove pulley are included.

Can ONLY for Saginaw Style Power Steering Pump
PUMP NOT INCLUDED!

Elect Power Steer Pump 12 VDC 1.8 GPM “For use w/max 75 CC Helm Control” ((((800 Max PSI))))

PUMP SPECIFICATIONS 1. VOLTS DC: 12, CONTINUOUS RUNNING "THIS MEANS NO STEERING HESITATION" 2. AMPS: NO STEERING 12, STEERING 22- 40, FULL LOCK 66 3. GPM: 1.8 4. DIMENTIONS: 11.500" TALL 6.000" WIDE 9.250" LONG 5. WEIGHT: 17.8 LBS

Twin Engine, Twin Power Steering Pump Priority Valve

Connects 2 engines / 2 power steering pumps (high pressure / return). Has -6 AN brass connections. Hard anodized billet body.

Upper Port Side Power Steering Mounting Bracket Assembly - BBC Head Mount

This power steering mounting bracket is designed for a upper port side mount on big block Chevrolet engines.  This heavy duty aluminum bracket is anodized black for corrosion protection (Note: picture shows satin finish).  This bracket accepts most popular GM power steering pumps and is supplied with the necessary mounting hardware.

Upper Port Side Power Steering Mounting Bracket Assembly - BBC Head Mount for Hardin Closed Cooling

This power steering mounting bracket is designed for a upper port side mount on big block Chevrolet engines.  This heavy duty aluminum bracket is anodized black for corrosion protection (Note: picture shows satin finish).  This bracket accepts most popular GM power steering pumps and is supplied with the necessary mounting hardware.

Upper Starboard Side Power Steering Mounting Bracket Assembly - Fits B/B Chevrolet

This power steering mounting bracket is designed for a upper starboard side mount on big block Chevrolet engines.  This heavy duty steel bracket is powder coated black for corrosion protection.  This bracket accepts most popular GM power steering pumps and is supplied with the necessary mounting hardware.

Power Steering Filter

• 3/8" NPT Inlet & Outlet
• 5" Length
• 1-1/2" Width

This filter is a high pressure low micron filter and is one of the best we've seen. This filter is an excellent accessory for any performance boat with external steering.

Power Steering Filter Element for 137-9037

• Replacment filter element only.
  

Titan Power Steering Reservoir

Hardin Marine, Powerboating's leader in hydraulic performance steering systems has designed the ultimate in power steering fluid control. These new Billet Aluminum/Lexan reservoirs provide a strong durable construction. The clear see through body provides easy, quick, visible oil level conditions. The ability to remotely deliver fluid to the power steering pump while allowing a baffled return port to limit aeration of your hydraulic steering fluid makes for easy plumbing.

Length: 6-3/4" x Width: 5-7/8" x Height: 9"

Mayfair Power Steering Reservoir - Tank Only

This Mayfair by Hardin Marine power steering reservoir is superbly crafted with internal baffling to eliminate foaming while reducing fluid temperature. It includes a vented leak-proof cap and is just one of the many Hardin Marine exclusives. Reservoir holds 36 oz. of fluid. No lines or fittings included.

Power Steering Reservoir - Plastic, with Brackets

Power Steering Return Dump Cap

This is the ultimate fluid return reservoir cap.  No welding is required.  This is one of the many features in our standard kit that makes ours better We actually do installation, so we actually know what fits, and what doesn't. Return fitting thread size is 1/4" NPT. NOTE: Only fits stock Mercury Power Steering Tanks. Does not fit any of our aftermarket tanks.